3 Easy Ways to Stop Fabric from Fraying - wikiHow (2024)

Explore this Article

Co-authored byKamel Almani

Last Updated: September 16, 2021References

Download Article

1. 1

   Use scotch tape for a quick fix. Lay your fabric on a hard, flat surface with the back facing up. With the fabric’s edge laid out in front of you horizontally, place the tape along the top of the edge. Cover about ¹⁄₂in (1.3cm) of the fabric’s edge with the tape. Let the excess tape fix the fabric loosely to your work surface. Cut a new, clean line through the taped fabric, below the fraying edge.^[1]

   • Leave the tape on the edge to keep it from fraying.
   • Scotch tape is a clear, adhesive tape. Select a matte tape as opposed to one with a glossy finish because it will be less noticeable.
   • This method will not last if the piece is washed, but it is helpful when cutting straight edges in hard-to-handle fabrics. It is also useful for pillows or other projects where the seams are hidden and subject to minimal washing.
2. 2

   Glue your edges with fabric glue, seam sealant, or super glue. Purchase any one of these adhesives at a local craft store or online. Simply place small dabs of glue along the edge of the fabric. Use a cotton swab or toothpick to spread the glue evenly. Avoid using too much glue as it can leave dark spots on your fabric once it has dried.^[2]

   • Alternatively, use the same process to apply the glue but then fold the glue-covered edge of the fabric over and press it down to create a hem.

   Advertisem*nt

3. 3

   Using pinking shears to cut a fresh edge. Pinking shears look like scissors with teeth and you can find them at any craft store or online. You use them as you would use scissors, cutting a new edge onto your fabric. Instead of a straight edge, however, the shears cut in a jagged-tooth pattern. This cut will prevent the edges from fraying.^[3]

   • This is a popular beginner-level method for dealing with fraying edges.
   • For additional stability, apply adhesive to the cut edge with a cotton swab or toothpick.

Advertisem*nt

Download Article

1. See Also

   Hand embroidery on clothes - the ultimate guideEmbroidery Finishing | Madeira Embroidery SolutionsThe Most Common Embroidery Mistakes (And How To Fix Them) | Embroiderers’ Guild of AmericaEmbroidery Stabilizers Made Easy | Your Complete 101 Guide

   1

   Cut and tie your thread. The low-tech and old-fashioned way to deal with a fraying edge is to fix it with a needle and thread. To begin, cut a length of thread that is around 18in (46cm) in length. Tie a knot in one end by looping the end around your forefinger, then push the shorter end through the loop, and pull it through.

2. 2

   Thread your needle. Take the unknotted end of your thread and grasp it between your thumb and forefinger. Loop it around the needle and slip the tiny loop off over the head of the needle creating a tight little loop. Flatten the loop between your fingers and then insert it through the eye of the needle until the loop pokes out the other side. Grasp the loop with your fingers and pull it through until the tail comes through.^[4]

   • You may need to cut a fresh end on your thread if it is a bit worn and floppy, as a soft piece of thread is difficult to work with.
   • Pull the tail through so that it is about 3–4in (7.6–10.2cm) in length.
3. 3

   Insert the needle from back to front to create a whipstitch.^[5] Hold your fabric with the front or finished side facing up. Starting at the back of the fabric, insert the needle as close to the edge as you can. Push the needle through the fabric to the front and pull the thread through until the knot catches.^[6]

   • Don’t pull too tightly or you’ll create a rumpled look on your edge.
   • Stay close to the edge, about ¹⁄₈in (0.32cm) or less is ideal.
4. 4

   Repeat your stitch to finish the edge. Place your needle again on the back of the fabric, next to the spot where you inserted it for your first stitch. Move on, repeating this same stitch across the length of your edge, always inserting the needle from the back to the front.^[7]

   • Space your stitches closer together for a tighter stitch or farther apart for a looser stitch.
5. 5

   Tie off the thread after the last stitch. Turn to the back of the fabric. Thread your needle under the last stitch and pull the thread under it until a small loop forms. Pull the needled through the loop and pull to create a knot. For more security, repeat this to make a second knot.^[8]

   • Cut the thread to finish the edge, leaving no more than an ¹⁄₈in (0.32cm) remaining at the end.

Advertisem*nt

Download Article

1. 1

   Use a serger to secure the edge. The most professional way to finish an edge is with a specialized sewing machine called a serger.^[9] This sewing gadget uses four threads and two needles. Thread your serger and feed your seam under the foot, moving it through your machine needles, as you would with any sewing machine.^[10]

   • Be careful to remove pins before feeding the fabric through the serger.
   • A serger sews, cuts, and finishes a seam all at the same time. For this reason, it can save you time.
   • A serger is a specialized machine that cannot replace all the more basic functions of a regular sewing machine. They cost a couple hundred dollars, but if you do a lot of finishing work this might be a good choice for you.
2. 2

   Try a zigzag stitch on your sewing machine. Set your sewing machine to the zigzag setting by using the dial or digital display on its side.^[11] Place the fabric under the raised foot of your machine.^[12] Lower the foot and proceed to feed the fabric through the machine. Keep the fabric’s edge lined up with the middle of the foot.^[13]

   • Refer to your machine’s manual for details if you’re unsure how to set it for a zigzag stitch.
   • Add a few reverse stitches at the beginning and end to knot the thread.
3. 3

   Use an overlock foot and your sewing machine to mimic a serger stitch. Remove the regular foot of your machine and attach the overlock foot in its place.^[14] Set your machine to do an overlocking stitch. Line your fabric up with the inner edge of the foot. Feed the fabric through the machine as usual.

   • By attaching an overlock foot to your sewing machine you can create a stitch that looks similar to what a serger creates.
   • Use a zigzag setting with the overlock foot to achieve a similar finishing effect if you don’t have an overlock setting on your machine.^[15]
   • Consult your sewing machine manual for details on switching out the foot. It is usually a matter of popping it off and on, no tools required.^[16]

Advertisem*nt

Expert Q&A

Ask a Question

Tips

Things You’ll Need

Finishing Without Sewing

Hand-Stitching the Edge

Using a Sewing Machine

19 votes - 89%