ARM vs x86: What's the difference? (2024)

Computers designed around ARM processors and those designed around Intel or AMD are not interchangeable. There are two foundational questions that each approaches in different ways:

• How do you balance transistor count and program complexity?

• How do you prioritize speed, power consumption, and cost?

The answers to these questions have guided technology innovation and software development in everything from smartphones to supercomputers over the past fourdecades.

An age-old debate among early programmers is what led to the divergence between two main philosophies in computer science: to simplify the programmer’s job, or simplify the microprocessor’s job.
To do anything productive with a computer, an operating system and the programs it executes need to interact with the Central Processing Unit (CPU), as well as other hardware like memory, storage, and network cards. The CPU mediates between the operating system (and running programs) and these pieces of hardware. To simplify the life of programmers, the CPU has a set of predefined actions and calculations called the instruction set or ISA (instruction set architecture). The operating system and the programs it executes (which are both written by programmers) rely on these instructions to perform low-level functions like:

1. Interactions between the CPU and hardware (memory, storage, network, etc)
2. Arithmetic functions (addition, subtraction, etc)
3. Data manipulation (binary shifts, etc).

The original x86 CPUs had (and still have) a very rich instruction set. A single instruction can complete an entire calculation (like multiplication) or move a chunk of data directly from one place in memory to another. This might not sound like much, but multiplication and moving data between places in memory requires a lot of instructions at this low level. With x86 computers, this complex series of operations can be executed with a single cycle. Processing units with this type of instruction set are called complex instruction set computers (CISC).

However, the powerful instructions in a CISC computer mean that it needs more transistors, which eat up space and power.

This led to several projects in the early 1980’s, exploring energy efficiency and ways to simplify the instruction sets in CPU architecture. Researchers discovered that in real life, most computers used only a small subset of the huge set of instructions provided in a CISC computer. This ultimately led to the design of reduced instruction set computer (RISC) processors. RISC processors have an instruction set where each instruction represents only a simple operation using lower power. This makes the assembly language programmer’s job more complex, but simplifies the processor’s job. With RISC processors and advanced RISC machines, complex operations are performed either by running multiple instructions or by pushing the complexity over to the compiler rather than the CPU core.

There are trade offs here. x86 CPUs tend to have very fast computing power and allow for more clarity or simplicity in the programming and number of instructions, but it comes at the expense of a larger, more expensive chip with a lot of transistors. ARM processors can be very fast for certain types of operations, but repeated cycles for individual instructions can slow it down as operations are more complex and more of the effort for defining and executing operations is pushed to the programming (and programmer) rather than the instruction set.

Also, because of these differences, MIPS (million instructions per second)—an approximate measure of a computer’s raw power—can be difficult to calculate since the different types of processors require different sets of instructions to perform the same activity.

RISC architecture was inspired by a need to make smaller chips with better performance for smaller computers—or microcomputers—which eventually became PCs. This introduced a second fundamental design question: Whether to focus on chip performance (processing speed—or clock speed) or energy consumption (power efficiency).

Since ARM processors are integrated as a SoC, the emphasis has long been on overall resource management, including low energy consumption and lower heat production. For example, ARM architectures (like ARMv8) tend not to have simplified cooling systems (no fans on a cell phone). However, x86 CPUs have tended to favor high-end processing speed over low power consumption.

While both CPU designs can still have high performance (both ARM- and x86-architecture supercomputers compete for the fastest in the world), ARM designs tend to focus on smaller form factors, battery life, size, eliminating cooling requirements, and—perhaps most importantly—cost. This is why ARM processors dominate small electronics and mobile devices like smartphones, tablets, and even Raspberry Pi systems. x86 architectures are more common in servers, PCs, and even laptops where there is a preference for speed and flexibility in real time, and fewer constraints on cooling and size.

ARM chips are becoming popular in high performance computing (HPC), and even cloud use cases (such as AWS Graviton and Azure)—two places where Red Hat Enterprise Linux provides a great platform for computation and compatibility, as well as app development, deployment, and optimization.

ARM CPUs have a long history with Linux systems, from Android-based systems for smartphones to custom systems for Raspberry Pi. Now, even one of the fastest supercomputers in the world uses Red Hat Enterprise Linux with ARM architecture (Red Hat powers Fugaku).

Unlike the x86 CPUs, the hardware for each ARM design is unique. This is where the power of a broad, open source community can help. Red Hat Enterprise Linux has a large community of hundreds of hardware vendors who are all tested and certified—and this includes ARM hardware manufacturers and designers. Red Hat has an early access program with our ARM partners to allow customers to collaborate and evaluate new ARM technologies.

Part of the power of Red Hat Enterprise Linux is its performance across different footprints, from cloud to servers to edge. The combination of technology, ecosystem, and consistent stability allows organizations to innovate and adapt wherever their IT needs to go.