- Categories
- Hobbies and Crafts
- Crafts
- Glass and Stained Glass Projects
- Working with Glass
Download Article
The best tools and methods for creating holes in plexiglass
Co-authored byEric McClure
Last Updated: February 4, 2024Fact Checked
Download Article
- |
- Preparing and Aligning the Drill Point |
- Driving the Drill Through |
- Video |
- |
- Tips |
- Things You'll Need
Plexiglass, also known as Lucite and Perspex is a type of acrylic.[1] Drilling through Plexiglass is notorious for causing it to crack, but with a round drill bit and low drill speed, this should be a breeze. Just take your time and make sure you have the right equipment. Here, we’ll walk you through the entire process so that you can drill clean, smooth holes without damaging anything.
Things You Should Know
- Put scrap acrylic or MDF sheets behind the Plexiglass you’re drilling to brace it and minimize cracking.
- Use a spiral drill bit designed specifically for plastic to slowly drill through the Plexiglass at the lowest drill speed.
- Use short bursts of low surges until the hole is drilled. If you smell burning, pour water on the hole as you drill.
Part 1
Part 1 of 3:
Safety & Setup
Download Article
1
Wear safety goggles. Acrylic can chip quite easily if you aren’t careful, so protect your eyes with protective goggles. If you’re working in an enclosed space with no ventilation, put on a dust mask or respirator, too.
- Drilling Plexiglass isn’t bad for your lungs, but the aroma of the melting acrylic from the drilling can be kind of unpleasant if you’re sensitive to strong odors.
2
Acquire some spiral drill bits designed for plastic. Plexiglas, the company that makes Plexiglass, explicitly says spiral bits are ideal when it comes to drilling through their products.[2] These bits have a different geometric structure that digs through acrylic more easily, so they’re less likely to crack the Plexiglass. Attach the bit to whatever drill you’re using based on the size of the hole you’re making.[3]
- Any drill will work with Plexiglass. You don’t need to use any special tools for this.
Advertisem*nt
3
Test the drill bit out on scrap acrylic, if possible. Practice with smaller pieces of scrap acrylic before attempting to drill into a large sheet. This will help you get a sense for the ideal speed. The hardest part of this process is getting the speed right, since too slow will cause the bit to skid while too fast will cause cracks.[4]
Advertisem*nt
Part 2
Part 2 of 3:
Preparing and Aligning the Drill Point
Download Article
1
Place your plexiglass sheet on top of a scrap piece. Set the acrylic you’re going to drill through on top of a sheet of damaged Plexiglass or MDF (medium density fiberboard). This will make it less likely that you will chip the back of the board or scratch it when the drill bit goes through.
- Some DIY enthusiasts have a lot of success putting painter’s tape around the sides of the area they’re drilling through.
- If there’s a protective film on the Plexiglass, leave it on. It’ll help minimize the odds of a crack.
2
Clamp the Plexiglass and backside to a secure surface. Use as many clamps as is necessary to secure the sheet. For larger sheets, you may need as many as 3-4 clamps. You can secure the sheets between two tables, two sawhorses, or even a single saw table.
- If you have adjustable C-clamps with custom pressure settings, don’t overdo it. So long as the Plexiglass is stable, it’s fine. If you over-tighten the clamps, you could shatter the sheet.
3
See AlsoPros and Cons of Acrylic Sheets | Cut MyDrilling Acrylic: Tips and TechniquesThe right screw for plasticsCan You Screw Into PlasticMark the dot you’re going to drill. Use a dry erase or permanent marker to indicate where you’re going to drill, since it can be kind of tough to stick to a spot on the clear Plexiglass. Also, make sure that the hole you’re drilling isn’t within 3–5 inches (7.6–12.7cm) of the edge of the sheet. Acrylic is notorious for chipping near the edge when it is punctured.[5]
- If you do need to drill near the edge, sandwich the acrylic between multiple sheets of MDF or acrylic and only leave the edge exposed.
- Acrylic and Plexiglass can be kind of hard to drill through since there are no points of reference. Marking the spot will help you keep track of where you’re working.
Advertisem*nt
Part 3
Part 3 of 3:
Driving the Drill Through
Download Article
1
Set your drill to a medium-low speed. Plug your drill in or place a charged battery inside. Then, turn the dial on the front of the drill to one of the lower numbers (if you have options from 20-1, 5 or under are ideal settings. Test the drill to confirm the drill bit is seated perfectly in the chuck.
- If the drill bit isn’t seated perfectly, unlock the chuck by twisting it counterclockwise and retighten it.
2
Run the drill slowly into the sheet at 90 degrees. Hold the drill steady over the mark you made at as perfect a 90-degree angle as possible. Maintain a moderate amount of pressure and slowly squeeze the drill. Work slowly in short bursts to ensure you don’t crack the acrylic.[6]
- If the drill bit skids, just reset and realign your drill bit against the Plexiglass.
3
Keep a steady, slow pace. Aim for a calm penetration rate as you continue to drill. Acrylic drill bits will produce plastic shavings, so once they start to surround the drill bit, stop and remove them to get a better view of what you are doing.[7]
- You can actually tell if you’re drilling at a healthy speed and energy by the shavings. If the shavings come off in thin, coherent sheets like you’re sharpening a pencil, you’re good to go.
4
Pour water on the cut if you smell or see melting. Plexiglass gets very hot when you drill into it, so it may start to melt if you’re drilling through anything thicker than a fraction of an inch. If you notice the area around the hole you’re drilling melting or you smell burning, stop and pour room-temperature water over the hole.
- Keep working until you’ve punched out the hole and repeat the process as needed!
- If your hole is too rough for your liking, deburr it by drilling through the hole again from the opposite side or by smoothing the inside down with sandpaper.
Advertisem*nt
Community Q&A
Search
Question
Is there a special bit needed to drill plexiglass?
Community Answer
There are special drill bits. They aren't "needed," but they are helpful and do a better job.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHowYesNo
Not Helpful 6Helpful 24
Question
How do I cut a square in the middle of a Plexiglas sheet?
Community Answer
You'll need a hand saw with a removable blade (like a hacksaw) and a drill bit that is a slightly larger diameter as the saw blade. Sketch the square in the location you want it on the material, then drill into the four corners of the square, taking care to make sure the hole doesn't cross over the square boundary you drew. Next, fit the blade through the hole and proceed to cut along the lines you've drawn. Cut the square a bit smaller than your final dimensions so you can go back with some sandpaper to clean up the cut, and use a sharp blade (use gloves!) to deburr and/or cut a chamfer into the edges.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHowYesNo
Not Helpful 1Helpful 8
Question
If I glue the plexiglass to the wood strip first, will that keep it from breaking when I drill it?
Community Answer
The trick is to go slowly, use a good sharp bit, and ensure that the section of material you are drilling is supported and will not bend, twist, or otherwise deviate from "flat". You could drill progressively larger holes, but in my experience this can cause chipping around the edges of the hole. Simply drill with the exact size you want, go slowly, and keep the cutting tool as close to perpendicular as you can.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHowYesNo
Not Helpful 0Helpful 9
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Advertisem*nt
Video
Tips
It is possible to drill acrylic with regular metal drill bits. However, the likelihood of melting, chipping, cracking, or breaking the acrylic is much higher. Ensure you go slow, stop often to cool the drill and always support the sheet.
Thanks
Helpful0Not Helpful0
Submit a Tip
All tip submissions are carefully reviewed before being published
Submit
Thanks for submitting a tip for review!
Advertisem*nt
Things You'll Need
- Safety goggles
- Round drill bits
- Clamps
- Medium Density Fiberboard (optional)
You Might Also Like
Advertisem*nt
References
- ↑ https://www.faa.gov/documentlibrary/media/advisory_circular/ac_43.13-1b_w-chg1.pdf
- ↑ https://www.plexiglas.de/en/service/processing/drilling-plexiglas
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.bcae1.com/plexi.htm
- ↑ https://www.todayshomeowner.com/video/tip-for-drilling-through-plexiglass/
- ↑ https://www.youtube.com/watch?v=rCSz1bWK_Ug
- ↑ https://www.youtube.com/watch?v=rCSz1bWK_Ug
About This Article
![How to Drill Plexiglass: A Step-by-Step Guide (32) How to Drill Plexiglass: A Step-by-Step Guide (32)](https://i0.wp.com/www.wikihow.com/images/thumb/d/dc/Eric_McClure.png/-crop-100-100-100px-Eric_McClure.png)
Co-authored by:
Eric McClure
wikiHow Staff Writer
This article was co-authored by wikiHow staff writer, Eric McClure. Eric McClure is an editing fellow at wikiHow where he has been editing, researching, and creating content since 2019. A former educator and poet, his work has appeared in Carcinogenic Poetry, Shot Glass Journal, Prairie Margins, and The Rusty Nail. His digital chapbook, The Internet, was also published in TL;DR Magazine. He was the winner of the Paul Carroll award for outstanding achievement in creative writing in 2014, and he was a featured reader at the Poetry Foundation’s Open Door Reading Series in 2015. Eric holds a BA in English from the University of Illinois at Chicago, and an MEd in secondary education from DePaul University. This article has been viewed 318,200 times.
2 votes - 50%
Co-authors: 9
Updated: February 4, 2024
Views:318,200
Categories: Working with Glass | Hole Making Tools
In other languages
- Send fan mail to authors
Thanks to all authors for creating a page that has been read 318,200 times.
Reader Success Stories
Sandy M.
Jun 5, 2017
"It was important to find out that I would need special drill bits and that I would have to make sure that they..." more
More reader storiesHide reader stories
If you buy through links on our site, we may earn a commission.
Did this article help you?
Advertisem*nt